Почему сыреет угол в доме: Что делать, если сыреют углы и стены в квартире или частном доме: способы устранения сырости

Почему сыреют углы в доме? Сыреют стены в частном доме что делать – Как устранить сырость в углах дома? Сыреют стены в частном доме что делать

В доме сыреет и покрывается плесенью угол что делать?

Что есть причина сырости? Образование конденсата на холодной поверхности.

В помещении где температура + и есть источники влаги, воздух всегда будет влажным. При этом влага может достигать критических значений, при которых может образовываться конденсат при соприкосновении с «холодными» поверхностями. Например для влажности 60% температура конденсации около +10град. ц. НО, если даже влажность в норме, т. е. порядка 50% тогда всеравно возможет конденсат, просто температура для его образования нужна ниже.

Решение проблемы:

Чтоб влажность была в норме, необходимо наличе простых удобств, типа ВЫТЯЖКА на кухне в сартирах и т. д. эти уникальные изобретения не позволяют зашкаливать влажности.

Если стены тонкие, или не соотвествуют теплотехническим нормам, тогда стена промерзает и имеет температуру благоприятную для образования конденсата. В таком случае стену надо утеплить, луче снаружи.

Особое внимание следует обратить на пароизоляцию, по технологии положено использовать специальные мембраны, которые снижают поток влаги через стену, но не исключают совсем. Если применить например пленку, тогда возможно поднятие влаги в помещениях, и это необходимо учесть в вытяжках, т. е. нужно увеличить их диаметр. Или использовать нормальные материалы. Тоже самое касается утепления изнутри, но кроме проблем с влажностью, возможно промерзание стены, т. к. изнутри она перестанет нагреваться как раньше, в сочетании с паропроницанием, это может вызвать неготивные явления, типа образование конденсата в теле стены. При наружнем утеплении это маловероятно. Поэтому если утеплять изнутри, тогда нужно применять тонкий утеплитель, например пенопласт 2-3см. с пароизолирующей мембраной, на стену. Или можно использовать пеноплекс, такой же толщины. НО, для пеноплекса мембрана не нужна, т. к. он сам задерживает пар, но не исключает совсем. Технически это выглядит как в документе на который я вам дал сцылку, стену обшивают и затем штукатурят, технологий обкатанная, для нее все сть на любом рынке.

Заслать скалолазов — утеплителей чтобы обклеили все стены пенопластом и заштукатурили

Я снял обои зачистил прогрунтовал с антисептиком промазал жидким стеклом и наклеил обои 2 зима пошла вроде чисто пока

Обработать раствором медного купороса и забелить потом

Мы при данной проблеме белили часто и в известь помешивали немного медного купороса. А вообще сейчас достаточно много различных белил, которые помогают бороться с плесенью, нужно вам проконсультироваться у менеджера специализированного магазина.

Утеплять стены.

Первое-выявить причину сырости и удалить ее… может в крыше проблемы и все ваши ремонты будут бесполезными

второе- отодрать все, что отдирается,

третье-просушить, сейчас топят, поэтому подождать -влага сама будет выходть …

ну и отделка пошла… пройти аквастопом, выровнять серой шпаклевкой. кнауф. и зашпаклевать белой… ну а там зачистить и окрасить

1.Обшейте этот угол листовым пенопластом. Сверху клеются обои и будет незаметно.

2.Сверлите стену и ставьте принудительную вытяжку в этом углу. (стоит маленький специальный вентилятор около 800 руб)

3.Купорос не поможет!

Причины могут быть разные.

1.Плохая вентиляция. Поставили пластиковое окно и наглухо закрыли приток воздуха, который раньше шел в щели.

2. Потеря стеной или перекрытием теплоизоляционных свойств. Происходит из-за увлажнения стены вследствие намокания внешнего (отливы, балконы, карнизы) или внутреннего (внутреннее от плохой вентиляции). Если верхний этаж, возможно слежался утеплитель на чердаке. Если угловая квартира, возможно выветривание материала стен. Если соседи сделали внутренее утепление стен, то ваша стена стала холоднее.

3. Отопление стало работать хуже.

1. Поискать причину увлажнения и по возможности устранить.

2. Продумать вопросы вентиляции и отопления.

3. Продумать возможность внешнего утепления

4. Крайний и самый худший вариант, сделать внутреннее утепление, но только после теплотехнического расчета, который должны сделать грамотные инженеры.

А вообще, если это квартира, обращайтесь в ЖКХ, пусть это станет их головной болью, а не вашей.

По материалам сайта: http://teplo-lis.ru

Сырость на стенах распространенная проблема — далеко не в одном доме, не в одной квартире, не одни хозяева переживают из-за того что одна из стен или угол комнаты становится сырым.

Проблемы, которые являются последствиями сырости в квартире, видимы и ощутимы, оттого и известны. Это и о

90000 How to Get Rid of Dampness and Humidity in the Home 90001 90002 The Problem of Dampness In the Home 90003 90004 Every house can suffer from damp problems, for many reasons, but there are certain things that will work for everybody to get rid of damp once and for all. If you are asking yourself, «Why is my house so damp?» then it is often quite simple to fix the issues. 90005 90004 90007 The two main reasons for dampness are: 90008 90005 90010 90011 Moisture can not escape 90012 90011 Water is getting in 90012 90015 90004 Quite often, it’s your lifestyle that’s causing condensation and possibly mold to build up inside your home.When I was growing up, my father was fastidious about opening a window in the kitchen, thereby not letting steam build up, and about wiping down condensation on the windows. It used to drive me mad, but now I know what he was trying to do. When I moved into an older house, I started to see what happens if you do not keep on top of moisture build-up as soon as the signs of dampness appear. 90005 90004 Some damp problems, like rising damp (the structural dampness inside the walls that indicates a breach in structure of a building, resulting in rain intrusion from outside or condensation from within) will need professional advice, but genuine rising damp is rare.90005 90004 Below, you will find three simple solutions to prevent dampness in your home. 90005 90002 1) Ventilate Your Home Properly 90003 90004 It’s common in the winter to keep the windows closed, and as a result, with modern draught-proofing, water has nowhere to go. 90005 90004 Condensation can result from tumble drying, baths / showers, or even just your own breath! The kettle boiling and food being cooked all release steam and moisture in the air which will find the coldest spot on your walls or windows and condense.From there, it’s a small step to becoming damp. Getting rid of dampness in your house sometimes means changing your own habits and adjusting your lifestyle. 90005 90004 All that water has to go somewhere, and if it can not get out, it will pool. Maybe you have some black mould on the bathroom ceiling or around window frames. This is a sign that the water vapour could not escape. 90005 90004 One solution is to install double-paned windows with two layers of glass to improve insulation. This will help with dampness as well as reduce the loss of heat.If you are having new double glazing fitted, you might also insist on trickle vents and keep them open. These vents at the top of windows give the damp air chance to escape, but you can always close them off if and when you want. 90005 90002 2) Get a Dehumidifier 90003 90004 Really. It’s that simple. A dehumidifier will suck in all the air in the room and squeeze out the moisture that causes damp and mould. The water collects in a small bucket in the unit which you empty. Move the dehumidifier around the house from room to room, wherever it seems needed.24-36 hours in each room is enough. 90005 90004 If your house is old, with no damp proof course (DPC), it might not look, smell, or seem damp, but I bet it’s in there! My house looks fantastic, but I put a dehumidifier into my bedroom 24 hours ago, and already it’s sucked nearly two pints of moisture from the air. 90005 90004 Stop suffering from damp today and scour the classified ads for a dehumidifying unit now. I would not live without one. 90005 90002 90007 Portable Dehumidifier 90008 90003 90004 You can get portable dehumidifiers that you can easily move around, from room to room or even from home to home.Our extended family shares a dehumidifier: No need for us all to own one! 90005 90002 Small Dehumidifier 90003 90004 There are small dehumidifiers available, too-for cupboards and small rooms, caravans, sheds, and lofts. Some will even fit on a windowsill. 90005 90002 3) Keep on Top of Wiping Down Mould 90003 90004 Become aware of where condensation collects in your house. Common places to find black mould are: 90005 90010 90011 Behind furniture, such as a sofa or a bookcase 90012 90011 In the corners of rooms 90012 90011 Under the window and accumulating on the window frame / window sill 90012 90011 Inside fitted cupboards and wardrobes 90012 90015 90004 If you just have a mild bit of mould discolouring, you can easily get rid of it by simply wiping it down with a wet wipe or a damp cloth.If it’s a bit more obvious, you might need to wipe it down with a damp and mould spray. Watered-down bleach works great, or check out what products are available at your local hardware store or supermarket. 90005 90004 Getting rid of damp and mould in your house is something that you need to keep on top of and solve. Damp walls can affect your belongings and your health, and it’s just not nice living in a damp house. Since most problems can be solved with just a short amount of time, investigating, ventilating, and getting a dehumidifier now will pay off in the long run.90005 .90000 What Causes Damp? | Homebuilding 90001 90002 All houses, whatever their age, contain moisture. It will be present in the building materials used and the air within the home. The natural tendency of moisture is to spread out from wet to dry areas, and also to move downwards under the influence of gravity, and your house construction should allow for this. 90003 90002 Simply put, dampness is just a localised excess of naturally occurring moisture. The excess is always caused by one of two things: 90003 90006 90007 either a sudden increase in the amount of moisture entering the building; 90008 90007 or a gradual local build-up of moisture caused by its inability to escape.90008 90011 90002 Dampness caused by a local build-up of moisture is often given a variety of names depending on where it shows up, such as ‘penetrating damp’ and ‘rising damp’. These names are both misleading and largely meaningless — the problem is almost always an excess of trapped moisture. 90003 90014 Damp in Old Homes 90015 90002 Unlike modern buildings, the construction of an older house is designed to prevent damp problems by preventing the excess build-up of moisture. 90003 90002 They were built almost entirely of permeable materials, with virtually no attempt at waterproofing in the modern sense, and so moisture will pass freely through the walls, floors and ceilings.Instead of being sealed into rooms as condensation, moisture inside the house is able to pass from room to room, and also pass through the external walls to the outside air. 90003 90002 Historically, most dampness was caused by the lack of maintenance leading to leaks. Nowadays, the majority of cases of damp in period houses are caused by inappropriate building work that stops moisture escaping. 90003 90002 With older solid walls it’s advisable to remove incompatible modern materials such as cement render or mortar pointing that trap damp.Replace with traditional lime-based breathable materials that allow moisture to evaporate. Allow time for walls to dry out and keep the house heated. 90003 90014 Obvious Causes of Damp 90015 90002 Dampness which is caused by any sudden increase in the amount of moisture entering the building usually appears without warning — and in a matter of hours. It can also disappear just as quickly in the early days. 90003 90002 The dampness associated with this type of problem is usually very well defined, as it is concentrated and intense.The cause of the problem is often fairly obvious too. 90003 90002 Any tiny drips from plumbing can be the cause of a large and intense damp patch — the escape of water may be small, but is often regular and concentrated on the same spot. This focused, repeated wetting quickly introduces more moisture than can escape, and the overload then spills into neighbouring areas. Hairline cracks in the grouting to bathroom wall tiles, when combined with ‘power showers’ can also be a recipe for damp in homes.90003 90002 90033 Check for: 90034 90003 90006 90007 corroded water pipes concealed in the walls 90008 90007 new plumbing for central heating, kitchens and bathrooms which drips when first used 90008 90007 failing waste pipes in older bathrooms 90008 90007 damaged seals around baths and showers 90008 90011 90002 When gutters at the eaves leak, water will either run directly down the outside of the wall for a short distance, or will splatter on the ground and window cills below. Leaks in other gutters often feed water directly into the roof space, and these can be extremely difficult to find.90003 90002 90033 Check for: 90034 90003 90006 90007 splattering from gutters splashing water onto walls 90008 90007 tracks of water in the roof which may be following roof timbers for several feet 90008 90011 90002 This normally means missing or slipped tiles or slates, but could also mean a worn out thatch, or a broken tile or slate. 90003 90002 Changes in the climate or the roof area since your house was first built may mean that the gutters are too small to cope with current rainfall.The only cure is to replace them for larger-capacity versions or increase the number of downpipes. 90003 90002 90033 Check for: 90034 90003 90006 90007 water spilling over the edges of the gutters on a regular basis 90008 90011 90002 The majority of buildings from the mid-17th century onwards rely on windows with outside cills that project beyond the face of the wall . The underside of the window cill incorporates a groove that sheds surplus rainwater clear of the wall. If the groove is blocked, all of the rainwater running down the outside of the window will be directed straight into the wall immediately below the window.90003 90002 90033 Check for: 90034 90003 90006 90007 grooves blocked with paint which cause large volumes of water to track down the wall 90008 90011 90002 These are also common weak points where water can seep into the walls. 90003 90002 90033 Check that: 90034 90003 90006 90007 roofs and chimney stacks have watertight flashings 90008 90007 chimney pots have been fitted with rain caps 90008 90011 90002 Old cast-iron downpipes can easily rust through at the back without anyone being aware.Also, downpipes that disappear straight into the ground at the bottom, or that contain any sharp bends, are very prone to blockage from debris washed in from the gutters. 90003 90002 90033 Check for: 90034 90003 90006 90007 holes in the back of a downpipe 90008 90007 water spewing back up out of down pipe joints 90008 90007 water tracking from the downpipe along brackets and to the face of the wall 90008 90011 90002 Get rid of humid air before it condenses into water and forms patches of black speckled mould.Install extractor fans on kitchens and bathrooms. Reduce emissions of water vapour, for example, by venting tumble driers to outdoors. Fit trickle vents to windows. It also helps if the wall surfaces are well insulated. 90003 90002 Clear any climbing vegetation, as it has a tendency to harbour damp and inhibit walls from drying out. 90003 90014 Less Obvious Causes of Damp 90015 90002 The cause of the damp is not always obvious, and there may be multiple defects that are all contributing to the cause.Although modern building work is often the primary cause of damp problems, there can be a delay of years before the dampness becomes noticeable, so the link is not always obvious. 90003 90002 Designed for use in dry walls, this type of treatment is incapable of working when installed in a wall that is already damp. They use either waxy creams that just form individual ‘fingers’ when injected, or chemicals dissolved in a water-based solvent. The solvents must completely evaporate away after injection to allow the chemicals to cure and form a water-repellent coating.90003 90002 If a wall is damp, the solvents never completely dry out and the chemicals never cure; the process will just saturate the wall with even more water. 90003 90002 The walls may be replastered with a waterproof cement plaster to try and hide any damp for the duration of the guarantee. This stops the natural movement of moisture — making any damp problems worse. 90003 90002 Used on the exterior of walls, this sort of coating develops cracks all over its surface. The size of the cracks depends on the quality of the render and skill of the builder, but they’re impossible to prevent.The cracks encourage water into the wall, but the water can not escape because the render is impermeable. 90003 90002 Even if cement render is not yet visibly cracked, it encourages condensation to form as moisture from inside the house can no longer escape — this process can even result in clay lump walls collapsing. 90003 90002 It is important that any excess moisture from below the floors can pass up through the floor and harmlessly into the air. If a floor is replaced with a modern solid design that prevents this from happening, moisture is forced to travel under the floor into the adjoining walls to escape.This will increase the overall amount of moisture in the base of the walls and potentially make those walls damp. 90003 90002 If the outside ground levels are correct and nothing on the outside of the walls prevents the moisture from escaping into the air, you may find only the internal walls are badly affected by the modern floor. 90003 90002 This too is relatively impermeable and so prevents moisture passing through. It may just form a thin layer over the original plaster, but in the worst cases, all of the original plaster will have been removed and replaced with waterproof cement render covered with a thin layer of pink plaster.90003 90002 Used directly on solid walls (inside or outside in the case of paint), these too are mostly impermeable and prevent moisture moving through the walls and escaping. 90003 90002 Cement mortars not only stop moisture moving freely through the wall and escaping into the air, but they also encourage water into the wall through cracks that always form in cement. These mortars also force natural salts to crystallise in brickwork, causing the bricks to break up. 90003 90002 Most below-ground rooms were cellars and cold stores which were an important part of the moisture control system.True cellar stores have their walls in contact with the ground and allow moisture to saturate them — ensuring they remain cool. 90003 90002 They are often built to intercept underground watercourses, and may have regularly flooded to a few inches. As nothing was stored on the floor or in direct contact with the walls, water and damp did not matter, and the flood water was used to save going outside to a frozen well or pump in winter. 90003 90002 Good ventilation allowed excess moisture to escape.If the cellars ever get converted into habitable rooms, the ventilation is stopped up — forcing moisture up into the rooms above. 90003 90002 This is almost guaranteed to be a problem. As a general rule, houses were always raised up above their surroundings. If the house was built with a brick paved ground floor, at the very least, this was laid on top of the existing ground level with a layer of fine ash or sand beneath to give a level finish. 90003 90002 Nowadays, you can often see old steps that once led up to doors, partially buried beneath later pavings.It is also common to see door thresholds that were originally above a top step, now below the adjoining ground so you step down to them. 90003 90002 External ground levels should be at least 200mm below floor level, so it is important to ensure that earth is not banked up against outside walls. Patios are often laid too high, causing bridging of DPSc or rain splashing on hard surfaces saturating the walls. Installing a shallow gravel-filled trench around the base of the wall assists evaporation of moisture.90003 90002 Formerly damp plaster can retain a residue of salts deposited by the water. Sometimes when rooms are heated after being left empty, dampness can reappear on the surface of the paster because these salts absorb moisture from the atmosphere of the room. Salts should be brushed or vacuumed off. 90003 90002 (90033 MORE 90034: How to deal with damp) 90003 .90000 How to get rid of black MOULD and damp in your house using this trick 90001 90002 How to get rid of black mould is something people often discuss. Whether it’s damp or mould, the first thing to do is find the cause. 90003 90002 Usually, it’s caused by excess moisture in buildings, which can result from leaking pipes, rising damp in basements or ground floors, or rain seeping in because of damage to the roof or around window frames. 90003 90002 In a newly-built home, damp can occur if the water used when the house was built is still drying out.90003 90002 A common place for mould to grow in your home is the bathroom. 90003 90002 The causes of this are lingering moisture caused by lack of ventilation, leaky toilets, sinks and plumping pipes and damp cellulose materials such as rugs, paper products, wood, wallpaper, grout, drywall and fabric. 90003 90002 90013 So how can mould affect your health? 90014 90003 90002 According to NHS Choices, damp and mould in the home can cause respiratory problems, infections, allergies and asthma, and it can also affect the immune system.90003 90002 GETTY 90003 How to remove mould: First, identify the cause 90002 GETTY 90003 How to remove mould: Your health can be affected in a number of ways 90002 Inhaling or touching mould spores can cause three types of symptoms: 90003 90002 Allergic reactions are the most common. When mould spores are inhaled, the immune system creates an allergic reaction due to the fact it’s trying to defend against foreign / unknown particles entering the body. 90003 90002 Mould infections can occur when mould spores are breathed into the body, allowing mould to grow inside them.90003 90002 In most cases, the infection can be treated with medication. The symptoms of a mould infection include skin irritation, excess mucus, athlete’s foot and nail infections. 90003 90002 There are a few dozen moulds that are particularly toxic to humans, and these moulds release highly toxic chemicals called mycotoxins. 90003 90002 In order for intoxication to occur by these toxic moulds, significant quantities are needed to intoxicate. 90003 90002 90013 How to remove black mould 90014 90003 90002 NHS Choices says you may be able to remove the mould yourself, or you may need to get a professional to remove it.90003 90002 Only remove mould yourself if it’s caused by condensation and covers an area less than one metre squared (1×1 metre or 3×3 feet). 90003 90002 Do not try to remove the mould yourself if it’s caused by sewage or other contaminated water. 90003 90002 Protect yourself from mould spores by wearing goggles, long rubber gloves and a mask that covers your nose and mouth. 90003 90002 Open the windows but keep doors closed to prevent spores spreading to other areas of the house. 90003 90048 How to prevent damp and mould in your house 90049 Sun, October 22 2017 90050 Mould: How to prevent mould and damp in your home.90051 90052 90052 90002 Getty 90003 90002 1 of 10 90003 90002 How to prevent mould and damp in your house 90003 90002 GETTY 90003 How to remove mould: Some you can remove yourself, other types you’ll need a professional 90002 Top tip: have a plastic bag ready to take away any soft furnishings, clothes and soft toys that are mouldy. These should then be shampooed and dried, thus getting rid of any spores. 90003 90002 Clothes with mould ideally should be professionally dry cleaned. 90003 90002 Next stop: fill a bucket or large bowl with mild soapy water.This could be washing up liquid or a soap used for hand-washing clothes — and put on some rubber gloves. 90003 90002 Use an old cloth or rag — something you can throw away — dipped in the pre-prepared soapy water to wipe the mould off the wall. 90003 90002 It’s important not to brush it, however, as this can release mould spores which is not ideal. When you’ve finished wiping away the mould, it’s imperitive you use a dry rag to remove the moisture from the wall. 90003 90002 All the moisture should be removed from the area with the rag.90003 90002 Afterwards, put the wet and dry rags in a plastic bag and throw them away. All the surfaces in the room should be thoroughly cleaned be either wet wiping or vacuuming to remove any spores. 90003 90002 These are the signs to look out for when spotting damp in your home. 90003 90002 90013 Is bleach safe to use on walls? 90014 90003 90002 Local council guidelines say existing mould can be removed by wiping down walls and window frames with a fungicidal wash that carries a Health and Safety Executive (HSE) approval or by using a diluted bleach solution.90003 90002 However some people say bleach should not be used on walls as it’s absorbent. 90003 90002 It’s worth noting you should never apply full-strength bleach to your walls, as this may permanently damage the paint or wallpaper. Always follow the guidelines on the packet. 90003 90002 90013 How to prevent damp 90014 90003 90002 Now you’ve dealt with the mould, it’s time to think about why your house might have it — and how to identify a damp problem. 90003 90002 There are various ways you can protect your home from damp but the most important is to keep on top of outdoor home maintenance.Check your roof regularly, keep gutters clear and inspect the pointing of any exterior brickwork. 90003 90002 Also, keep your home warm whenever a cold snap arises. 90003 90002 Properly fitted double-glazing on your windows will help to protect against too much condensation — try to maintain a constant temperature. 90003 90002 Ventilation is also key, in areas where moisture is produced, like laundry rooms, try to keep the air flowing with an extractor fan or cracking a window. 90003 90002 Remove excess moisture 90003 90002 Using a dehumidifier will help to remove excess moisture from the air, leaving your home feeling warmer and more comfortable.90003.90000 The best ways to prevent damp in your home 90001 90002 90003 90004 Condensation can cause damp anywhere and once it’s taken hold, it can be difficult to get rid of. As well as looking pretty horrible, damp and mould can lead to structural problems and health issues too. As with anything, it’s easier to prevent these problems than to treat them. 90005 90003 Here are our top tips for fending off damp in your home. Most are easy and inexpensive, but we’ve also thrown in a couple of long-term fixes which have higher installation costs.90005 90008 Ventilation 90009 90003 Whilst home improvements such as double glazing save energy, they also increase the relative humidity inside a property. A lot of water vapour is created inside the house by everyday activities such as cooking and showering. This warm water vapour tends to settle on (cold) walls, sometimes leading to interstitial condensation. This is when moist air penetrates the wall, roof or floor where it reaches the dew point and condenses into liquid water. As you might imagine, this might be hidden or hard to treat, so it can easily lead to damp and mould.90005 90003 So what can you do about it? Make sure to use an extractor fan when cooking or showering and ensure some ventilation at all times. Also dry your washing outdoors when possible. You can have expensive ventilation systems installed, but in most cases, a combination of extractor fans and windows will do just fine. Even when it’s cold outside you should crack a window from time to time — or at least make sure your trickle vents are open. This is one of the easiest and most effective ways to prevent damp.90005 90003 On a side note — make sure your furniture is not sitting flat against the walls. This way, air can circulate behind it, discouraging condensation from setting on the walls. 90005 90008 Insulation 90009 90003 Insulation (whether internal or external) raises the temperature of walls so that water vapour is less likely to condense on them. Condensation occurs when a surface is colder than the water vapour. By insulating your walls, you’ll reduce the temperature difference between the two.90005 90003 You might already have cavity wall insulation, or some loft insulation, but you do not have to stop there. Choosing which type to go for normally comes down to budget. Loft and floor insulation can often be installed yourself, and there’s a big choice when it comes to materials. Sheep wool, for instance, has the extra damp-fighting property of helping to regulate humidity. 90005 90003 Internal and external solid wall insulation are installed by professionals in almost all cases.Both can be pretty expensive — especially EWI — but they can pay back in the long run in energy savings. Plus (provided you use ventilation) they make damp less likely. 90005 90008 Heating 90009 90003 Being smart about your heating can also help prevent damp. Some people believe that the warmer their house is, the less likely it is to attract damp. This is not really true, especially if you’re not ventilating it properly. However, there is one type of heating which actively fights the formation of damp: infrared.90005 90003 90005 You might have seen far-infrared heating in action — these are the glowing red heaters often used outdoors. Recently they have been beaten in terms of popularity by the more modern near-infrared heating panels. 90003 These panels work through (safe) radiation, meaning they heat the fabric of the building — and the people inside it — directly. Heat is then stored in thermal mass, even after the heaters are turned off. So infrared can really help to dry out walls if they are affected by damp — as long as there are no underlying issues.They can stop walls getting cold enough for water to settle on them. 90031 90005 90008 Dehumidifying 90009 90003 Another option for discouraging damp is to get a dehumidifier. These units run off electricity and pull in damp air from around them, lowering humidity levels. They either contain some kind of reservoir for collecting water when it condenses, which must be emptied regularly, or they can be attached to a hose which runs water off down a nearby drain. They then heat the air back up before returning it to the room.Some of them have built-in humidistats, which allow the unit to run until humidity levels have dropped below a certain level, and then shut off automatically. 90005 90008 Render 90009 90003 Damp can also be caused by rainwater leaking in through cracks in the brickwork. This penetrating damp (as opposed to rising damp, which can be much harder to treat), rendering your external walls can be a great fix — as long as you dry the wall out first. Like the external wall insulation mentioned above, rendering is not cheap — but the render will form a protective waterproof barrier on the external walls, repelling water and preventing water ingress in future.It can also really smarten up your property. 90005 90008 Looking for an installer? 90009 90003 Thinking about having your property rendered or heating system updated? We have scoured the country for the best tradespeople, so that we can make sure we only recommend those we really trust. 90005 90003 If you would like us to find you a local installer, just fill in the form below and we will be in touch shortly! 90005 .